Экономика и менеджмент \ Управление сетями связи

Network Configuration Requirements. Board Configuration Requirements. Equipment-Level Protection Configuration Requirements, страница 3

A.2  Board Configuration Requirements

A.2.1  Cross-Connect Board

Configure a cross-connect board depending on the service capacity and the increase tendency. Select the cross-connect board according to the requirement in Table A-2.

Table A-2 Configuration requirement of cross-connect board

Board type

Higher order cross-connect capacity

Lower order cross-connect capacity

Function

Configuration mode

GXCSA

40 Gbit/s

5 Gbit/s

Used for the main subrack and does not support extended subrack

1+1 hot backup (slot 9, slot 10)

EXCSA

80 Gbit/s

5 Gbit/s

Used for the main subrack and does not support extended subrack

UXCSA

80 Gbit/s

20 Gbit/s

Used for the main subrack and does not support extended subrack

UXCSB

80 Gbit/s

20 Gbit/s

Used for the main subrack and supports 1.25 Gbit/s extended subrack

XCE

0

1.25 Gbit/s

Used for extended subrack (Note)

Note: Adopt the OptiX OSN 3500 as the extended subrack.

A.2.2  SDH Board

1.  Slot Requirement

Table A-3 shows SDH boards and the corresponding slots.

Table A-3 SDH boards and slots

Board type

Slot for 40 Gbit/s cross-connect capacity

Slot for 80 Gbit/s cross-connect capacity

SL64/SF64

Slot 8, slot 11

Slot 7, slot 8, slot 11, slot 12

SL16

Slots 6–8, slots 11–13

Slots 5–8, slots 11–14

SLQ4

Slots 6–8, slots 11–13

Slots 5–8, slots 11–14

SLD4

Slots 6–8, slots 11–13

Slots 1–8, slots 11–17

SL4

Slots 1–8, slots 11–16

Slots 1–8, slots 11–17

SLQ1

Slots 1–8, slots 11–16

Slots 1–8, slots 11–17

SLD1

Slots 1–8, slots 11–16

Slots 1–8, slots 11–17

SL1

Slots 1–8, slots 11–16

Slots 1–8, slots 11–17

 Warning:

Do not configure an ADM of a ring network using the optical interfaces on the same optical interface board (such as SLQ4, SLD4), because if the board is faulty, the ADM will fail in both directions. In this case, the optical interfaces at both ends of an ADM should be on two boards.

2.  Optical Module and Parameter Requirement

Table A-4 shows the types and parameters of the optical modules provided by SDH boards.


Table A-4 Types and parameters of optical modules provided by SDH boards

Transmission rate

Corresponding level

Wavelength (nm)

Transmission distance (km)

Launched optical power (dBm)

Receiver sensitivity (dBm)

STM-1

I-1

1310

2–15

–15 to –8

–23

S-1.1

1310

2–15

–15 to –8

–28

L-1.1

1310

15–40

–5 to 0

–34

L-1.2

1550

40–80

–5 to 0

–34

Ve-1.2

1550

80–100

–3 to 2

–34

STM-4

I-4

1310

2–15

–15 to –8

–23

S-4.1

1310

2–15

–15 to –8

–28

L-4.1

1310

15–40

–3 to 2

–28

L-4.2

1550

40–80

–3 to 2

–28

Ve-4.2

1550

80–100

–3 to 2

–33

STM-16

I-16

1310

0–2

–10 to –3

–18

S-16.1

1310

2–15

–5 to 0

–18

L-16.1

1310

15–40

–2 to 3

–27

L-16.2

1550

40–80

–2 to 3

–28

L-16.2Je

1550

80–100

5 to 7

–28

V-16.2Je (Note)

1550

100–140

5 to 7

–28

U-16.2Je (Note)

1550.12

140–170

5 to 7

–33

STM-64

I-64.1

1310

0–2

–6 to –1

–11

S-64.2b

1550

2–40

–1 to 2

–14

L-64.2b(Note)

1550

70

1 to 4

–14

Le-64.2

1550

60

1 to 4

–19.5

Ls-64.2

1550

80

3 to 5

–21

V-64.2b (Note)

1550.12

70–120

3 to 5

–23
Скачать файл