Determining of the mathematical model heater systems of the stem of shaft, страница 4

In the application block diagrams of the local automatic control system of regulatory type of a level represented, and also diagrams of transient phenomenons of systems are instanced at feed on control channels and agitations of single jump effect and effect as noise.

In the appendix block diagrams of local system of automatic regulation of a level represented, and also diagrams of transient phenomenons of systems at feed on control and disturbance channels of single jump effect and effect as noise.

CONCLUSION

The carried out analysis has shown efficiency of realization of program automatic control of process through industrial controllers, not looking on imposing of some restrictions on a conclusion of mathematical model of process. The put forward requirements to a designed control system as have been satisfied by means of a choice of a principle of construction of a control system. The choice of engineering tools of automation fitted to the specified conditions. It has in turn led to the competent coordination of output parameters, a measurement accuracy, ranges of change of parameters and other operating conditions of devices and devices of the control and regulation of temperature of the heat-transfer agent with similar parameters and operating conditions of the managing computer.

As a result of simulation of the given process in mathematical pack MATLAB "Simulink", satisfactory outcomes have been obtained, that once again confirms its practical significance.

REFERENCES

[1] S.B.Mihalev, J.G.Strotsev, J.A.Shabad, J.G.Butkov, Automation of managerial processes in floppy industrial systems 1986.

[2] V.I.Mahnach, Automation of processes of technological preparation of manufacture. Scientific research publication. / АS Byelorussia, Inst. techn. cybernetics, 1993.

[3] Automation of technical training of manufacture: Scientific research publication. / AS BSSR, 1988.

[4] R.S.Sedegova, Automation of management in instrument making and mechanical engineering on the basis of SM of the COMPUTER and the micro-computer: Scientific research publication. 1983.

[5] L.M.Matjushkov, M.A.Samoshkin, A.G.Machnev, etc, The automated workplaces in control systems. 1985.

[6] S.G.Basiladze, V.M.Repina, Computing methods and hardware-software maintenance in scientific researches.  1992.

[7] Babochkin B.A., A supply with information of the control information system of power supply systems, 1974.

[8] V.P.Gorjachkina, V.T.Sergovantsev, Modelling and automation of technological processes of an agricultural production, Scientific research publication, М., 1978.

[9] Bychkov, Application of industrial programmed controllers for automation of techno-logical processes: The manual at the rate "Programmed controllers and MPC" / М., 1992.

[10] A.V.Korolev, V.V.Bolkunov, A.A.Gerasimov Designing technological processes in the floppy automated manufacture: Studies. The manual for students; Saratov. 1992.

[11] The collection of theses of reports of X students and post-graduate students Republic Belarus scientific conference., vol.2, A.G. Zakharov

[12] Mike Predko, A manual on microcontrollers.Т. 1: In 2 т. 2001.

[13] Kyzmizki I.F., Kobrynets V.P., Ovsiannikov A.V. Simulation of objects and control systems: The manual for students. - Minsk.: BSTU, 2003. - 212с.

[14] G.T.Kulakov Analys's fists and synthesis of systems of automatic control: The manual. - Minsk.:"Technoprint", 2003. - 135с.

[15] Medvedev V.S., Potemkin V.G. Control System Toolbox. MATLAB 5 for students. - М., 1999. - 287с.

[16] Metiuz J, Fink G, Kurtiz D. Numerical methods. Use MATLAB, 3 edition.: Trans. with English - М.: the Publishing house "Williams", 2001. - 720с.